IBANEZ S520EX MANUAL PDF

The SEX is an S series solid body electric guitar model introduced by Ibanez in It was initially produced in Korea and then later in Indonesia. There’s no way a guy who does a couple guitar setups every day of the year would do a better than someone will with instructions from the. For over 18 years, Ibanez RG guitars with Edge double locking sys- tems have been SEX MOF. • 3pc Wizard II Manually Adjustable Zero. Point System.

Author: Sajin Fenribar
Country: Turks & Caicos Islands
Language: English (Spanish)
Genre: Sex
Published (Last): 22 September 2016
Pages: 239
PDF File Size: 15.54 Mb
ePub File Size: 20.30 Mb
ISBN: 857-7-37621-534-3
Downloads: 55778
Price: Free* [*Free Regsitration Required]
Uploader: Vik

All guitar necks are subject to great stress as a result of string tension, humidity or changes in climactic conditions. If the intonation is still not correct repeat steps 1, 2 and 3. Loosen the pressure pad screws on the top lock with a 3mm allen wrench and loosen the string to be adjusted. Play the harmonic at the 12th fret, compare it to the fretted noteat the 12th fret, these notes should read the same on the tuner. Raise or lower the tremolo to the desired string height using a 4mm allen wrench.

All lbanez guitars use A for a standard pitch.

Thread the new string through the string holder tubeand over the saddle pulling it tight towards the headstock. Always loosen the Stud lock screws counter clockwise with a 1. Tighten the string stopper bolt. The height adjustment of manula tremolo can be set by using the amnual 4mm adjustment screws 2 on either side of the tremolo unit.

Loosen the pressure pad lock screws on the top lock with a 3. Play the harmonic at the 12th fret, compare it to the fretted note at the 12th fret, these notes should read the same on the tuner.

TOP Related Articles  TISSUE ENGINEERING PALSSON BHATIA PDF

SEX (–) | Ibanez Wiki | FANDOM powered by Wikia

Cut off the ball end of the new string above the string winding and insert the end of the string in between the main saddle and the String holder block. Occasionally, there are times when the neck may need adjustment. If the 12th fret harmonic is higher than the fretted note, the saddle needs to be moved forward. Loosen the Saddle lack down screw 9 on the saddle to be adjusted with a 2mm allen wrench. Loosen the heigth adjustment screw 5 on both sides of the bridge using a 2 Phillips.

Remove the tremolo cavity cover plate from the back of the body. Tune the guitar to pitch and recheck the intonation.

Wiring Diagrams

Loosen the heigth adjustment screw 5 on both sides of the bridge using a 2 Phillips 2. Tighten the String stopper Screw.

Before adjusting the intonation, first determine the direction that the saddle needs to be moved. If the intonation is still not correct repeat steps 2 and 3.

S520EX (2005–2009)

This adjustment should be performed periodically and only by qualified repair personnel. Over adjustment can result in damage to the instrument and will no be covered under warranty. If this happens, replace the arm bushings with new ones. To replace the bushings, remove the bushings by spreading opening the bushing until it is removed.

Turn the Arm torqueadjustment nut turns counter clockwise. Use an electronic tuner and tune the guitar to a standard pitch.

If the 12th fret harmonic pitch is lower than the fretted note, the saddle needs to be moved back. Raise or lower the tremolo to the desired string height using a 3mm allen wrench. Note For ease in retuning. When the guitar is properly adjusted, tighten the top lock pressure pad screws. Tremolo Angle Adjustment The tremolo system should sit parallel to the surface of the guitar body, as shown in jbanez illustration.

TOP Related Articles  CEKAF PDF

To check the intonation: To adjust the string height of the saddles use a 1. Adjusting the string Height. Intonation mabual is usually necessary when new strings are fitted it can also be affected by the angle of the tremolo unit. To change the strings angle adjust the two 2mm 6 screws on the highside of the bridge, chanding the pivot angle. Tighten the pressure pad screws. S20ex the intonation is performed by moving the individual string saddles forward or backward.

Using a Phillips head screwdriver, turn the spring tension adjustment screw and adjust the length of the spring.

Manuql tremolo arm is placed in the hole in the bridge plate and inserted into the threaded block. Adjust the saddle forward or backward to the proper position and tighten the Saddlelock down screw 9.

After changing the desired strings retune all the strings to the proper pitch and tighter the top lock pressure pad screws.